Wiring harness routing & packaging Rules Week 3 Challenge

BACK DOOR WIRING HARNESS PROJECT AIM Build a wiring harness for a given automobile body and Prepare flatten view drawings in CATIA V5 that contain packaging rules. Industry best practises learned in this course must be represented in design. All essential reports, including clearance, clipping/clamping selection, harness…

WIRING HARNESS OF 16 VALVE ENGINE PROJECT   AIM Design the Wiring Harness on the Given Engine and prepare a flatten view drawing in CATIA V5 according to specific packaging guidelines, quality standards, and necessary reports like clearance, clipping, harness fixing requirements, harness continuity, and any necessary…

Aim Take a model, then flatten the harness assembly that was finished for the "week 4 challenge." The flattened view should be placed on a drawing page. Make certain that packages with protective covers have distinctive visuals in the drawing view. Wiring Harness  A wire harness model and components from the Week…

Aim Use the electrical workbench to route the following harness arrangement. Make a guess as to the diameters of the harness bundles. Utilize the connections offered. Check the continuity of the bundle when routing is finished. Add a picture of the outcome to the submission, and annotate each connector. Assume that annotations…

Aim  In the electrical workbench, arrange the following harness setup. Make a guess as to the diameters of the harness bundles. Utilize the connectors below as stated in the configuration design. Every branch that is attached to a DT06-2S or DT06-4S connection should have a protective covering. maintain the 30mm end…

Q1) Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. ANSWER: P CLAMP The P-Clamp from TE Connectivity (TE) offers a compact, quick, and effective way to instal cable harnesses. The whole cable diameter range of (21) AS21919…

AIM Use the provided link to get the connections and connector clip cad files, then describe it as an electrical connector using the Electrical Part Design Workbench. Give Connectors & Clip all the appropriate characteristics. DT06-08SA Connector Connector & Housing Type: Housing for Female Terminals Mating…

AIM Utilizing MATLAB, simulate the thermal impacts and evaluate life cycle performance at various temperatures, charge & discharge rates for a 10 cell series lithium ion battery model. NANOPHOSPHATE LITHIUM IRON PHOSPHATE (LIFEPO4) ANR26650M1-BATTERY TECHNOLOGY The high-performance Nanophosphate lithium iron phosphate…

MECHANICAL DESIGN OF BATTERY PACK A PROJECT   Aim Prepare a thorough battery pack with an 18-kWh capacity, and each cell's enclosure and ANR26650M1-B drawing should be included. Objective of this Project  By utilising two key categories in this project—ANR26650M1-B cells and Permanent Magnet Synchronous…

AIM: Develop and evaluate lithium ion battery management algorithms, simulate the three test scenarios from the harness dashboard, and write a thorough report on the findings. SIMULINK MODELS FOR BMS ALGORITHMS USED IN THE PROJECT 1. Calculate the State of Charge using the Extended Kalman Filter and Unscented Kalman Filter.2.…

1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it LITHIUM ION BATTERY A lithium-ion battery, often known as a Li-ion battery, is a type of rechargeable battery that stores…

AIM Utilizing Simscape Multibody and Simscape components, make a model of a double-acting actuator. The hydraulic system must be modelled using Simscape library physical components, and the mechanical system of the cylinder must be constructed using Simscape Multibody library components. CYLINDER MODEL  The cylinder…

CONSTRUCTION OF A P1 HYBRID VEHICLE AHEAD ENERGY-BASED FUEL CONSUMPTION MODEL   OBJECTIVE The main objective of this project is to model a P1 hybrid and to comprehend how it works. For this project, the Honda Insight motor and battery are taken into consideration, and data is then obtained from the ADVISOR data source…

DEALS WITH THE DEVELOPMENT OF FORWARD DEVELOPMENT OF A FORWARD ENERGY BASED FUEL CONSUMPTION MODEL OF A CONVENTIONAL VECHILE     OBJECTIVE  For the goal of estimating the driver, controller, and powertrain, construct a fuel-based conventional vehicle model utilising the UDDS and HWFET drive cycle, and plot…

SPEED CONTROL OF A DIRECT CURRENT DC MOTOR A PROJECT   OBJECTIVE For the function of designing and developing the PID controller for a DC motor, an approximate Matlab programme was used. From there, a set of equations was developed using the Simulink model, and the AIM Using a PID controller, a dc motor's target speed…

DATA HANDLING AND INTERPOLATION A PROJECT   OBJECTIVE To design and develop the appropriate MATLAB programmes for getting and handling the data from the supplied Excel file. AIM Utilize the accompanying voltage and current data from an Excel file as an input to a MATLAB program to interpolate the data inside the specified…

 NOTE : Project analysis for a practical automotive electrical circuit is submitted in pdf format. Kindly validate it.