We have to first make the solid body from the class A surface. We should be start with the first with create with the tooling axis for creating the tooling axis we have select the edge which are to be create the issue for the draft or plastic mold. So, we have to do the draft analysis for the plastic mold so we have to…
Manthan Waghaye
updated on 21 Dec 2023
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by Manthan Waghaye (30)
Week 10 - Challenge 3 - Door Trim Lower with Engineering Features
We have to first make the solid body from the class A surface. We should be start with the first with create with the tooling axis for creating the tooling axis we have select the edge which are to be create the issue for the draft or plastic mold. So, we have to do the draft analysis for the plastic mold so we have to…
21 Dec 2023 12:27 AM IST
Week 11 - Project - A pillar Design with Master Section
We have to first make the solid body from the class A surface. We should be start with the first with create with the tooling axis for creating the tooling axis we have select the edge which are to be create the issue for the draft or plastic mold. So, we have to do the draft analysis for the plastic mold so we have to…
04 Nov 2023 05:02 PM IST
Week 4:- Pin Unit Design Challenge
To design two different type of fix pin unit with different Pins, Riser, Blade, and Block and two retractable pin unit with Different Pins, Riser, Blade, Cylinder, and Block. Fix pin unit: Fixed pin unit is a unit designed to locate the car panel using pins.table Pin, pin retainer, shims, blocks, blade,…
22 Oct 2023 04:37 PM IST
Week 3:- BiW Fixture Design Methodologies Challenges
1)What is Design Methodology? Design methodology - It is nothing but the steps followed during the Concept designing stages of fixture design. Design methodology is divided into the following sub parts: - 1.Purchase Order: A purchase order is the order from the customer end for the starting of the work. A purchase…
10 Oct 2023 04:26 PM IST
Week 10 - Challenge 2- Attachment Feature Creation (Dog House)
We have to first make the solid body from the class A surface. We should be start with the first with create with the tooling axis for creating the tooling axis we have select the edge which are to be create the issue for the draft or plastic mold. So, we have to do the draft analysis for the plastic mold so we have…
07 Oct 2023 06:14 PM IST
Week 2:- BiW Fixture Basics Challenge
1. What is the process of project execution activity? 1)RFQ received - RFQ stands for Request for Quotation. In this customer specifies his requirements,specifications etc. in form of documents or data. Also customer specifies its Technical offer, commercial offer, how the project will be executed & timeline to complete…
02 Oct 2023 01:30 PM IST
Week 10 - Challenge 1- Attachment Feature Creation (Ribs & Screw Boss)
We have to first make the solid body from the class A surface. We should be start with the first with create with the tooling axis for creating the tooling axis we have select the edge which are to be create the issue for the draft or plastic mold. So, we have to do the draft analysis for the plastic mold so we have to…
27 Sep 2023 02:10 AM IST
Week 1:- Introduction to BiW and Fixtures Challenge
1. What is BIW & define its parts? To industry body manufacturer in segment like does, engine, roof, closures etc. All the parts are used to join and make Complete body structure. At the end of framing line body receive door bonnet, tailgate and front wings which have been built separately. ORBody in White (B.I.W.)…
24 Sep 2023 01:06 PM IST
Week 9 - Challenge 3 - Bumper
We should be start with the first with create with the tooling axis for creating the tooling axis we have select the edge which are to be create the issue for the draft or plastic mold. So we have to do the draft analysis for the plastic mold so we have to analyze the part for creating the dummy axis and then we have to…
10 Sep 2023 04:59 PM IST
Week 9 - Challenge 2 - Switch Bezel Design
Switch Bezel Design We should be start with the first with create with the tooling axis for creating the tooling axis we have select the edge which are to be create the issue for the draft or plastic mold. To get the proper view of wall and the base surface we give the color to the surface. So we have to do the draft analysis…
04 Sep 2023 04:40 PM IST
Week 9 - Challenge 1 - Base Bracket Design
Base Bracket Design We should be start with the first with create with the tooling axis for creating the tooling axis we have select the edge which are to be create the issue for the draft or plastic mold. So we have to do the draft analysis for the plastic mold so we have to analyze the part for creating the dummy axis…
02 Sep 2023 09:51 AM IST
Week 7 Challenge - Assembly Workbench
ASSY_QUICK_RETURN_MACCreate a single part of the assembly Assemble parts in catia ASSY_CV_JOINTCreate a single part of the assembly Assemble parts in catia
15 Aug 2023 05:40 AM IST
Project 1
For making any Harness assembely we have to first we have to know the component or connector and their position in the harness assembely and then define this connector as the electrical part so. we have to define its connector connection point and bundle connection point and some time as cavity connection if…
15 Feb 2023 04:54 PM IST
Week 14 challenge
Assemble and apply GD&T to the butterfly valve assembly drawing A butterfly valve is a regulating and shut-off device that can be an alternative, in some applications. Although the stem is a very small item when compared to other parts of butterfly…
09 Jan 2023 10:21 AM IST
Fender Design - Wheel Arch Challenge
Fender objective:- To Calculate the wheel arch radius for the given Fender model and check for its eligibility to pass the European Standards. Introduction:- Fender is the US English term for the part of an automobile (vehicle body) that frames a wheel well (the fender underside). Its primary purpose is to…
13 Oct 2022 07:03 PM IST
Roof Design
Roof Design OBJECTIVES: Create a roof of the car by the given styling surfac based on the master section provided.To validate the designed roof is satisfy the heat distortion criteria and snow load condition. ROOF INTRODUCTION: An automobile roof or car top is the portion of an automobile that sits above the…
13 Oct 2022 04:02 AM IST
Radar Mast & Final Assembly of Yacht
Modelling Sunseeker Predator Yacht Objective :- To create the Model of a Sunseeker Predator Yacht in Solidworks using the various types of sketches and the features tool form the solidworks. Also create photorealistic…
20 Aug 2022 04:54 AM IST
Photo Realistic Rendering
Modelling American chopper Objective :- To create the Model of a American chopper in Solidworks using the various types of sketches and the features tool form the solidworks. Also create photorealistic rendered image of American…
19 Aug 2022 06:49 PM IST
Section Modulus calculation and optimization
Section Modulus : Section Modulus is the geometric property of the given cross-section of any shaft or beam structures. It is the direct measure of the strength of the shaft section or the beam section. Higher the section…
03 Jun 2022 06:03 PM IST
Hood design-Week 2
Hood Design :- The important criteria for the car sheet metal design is hood design. It is the protection of the engine components and for front collision. The design of hood should such that when front collision is occurs then force act on it should be go upward direction through the…
28 May 2022 06:15 PM IST
Underbody Coating
Underbody coating :- Underbody coating is usually a dense cladding applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership…
16 May 2022 10:53 AM IST
Benchmarking
Benchmark :- It is comparison between the similar products services or processes on some diamensions of performance. OR It is the process of measuring products, services, and processes against those of organizations known to be leaders in one or more aspects of their operations.Their are two type…
15 May 2022 08:11 PM IST
Project 2
For making any Harness assembely we have to first we have to know the component or connector and their position in the harness assembely and then define this connector as the electrical part so. we have to define its connector connection point and bundle connection point and some time as cavity connection if it is needed…
11 May 2022 05:53 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 7 Challenge
Flatten the harness assembly :- For this we have to first take parts as connector and make it as a electrical component and then in assembley design make the position of it as given above.…
15 Apr 2022 07:02 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge
For routing the harness we have to define the component first as a electrical part for this we have create the two harness as A and B . Harness A :- define the all connector as follow:- In this way we have to define all the connector and then we have to position…
14 Apr 2022 05:38 AM IST
Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge
Harness Assembly It is product which contains geometrical bundle & electrical bundle which have electrical circuit information.For making the harness assembly we have follow the some step as follow:- Step 1:- Inserting the components:- …
07 Apr 2022 03:33 AM IST
Wiring harness routing & packaging Rules Week 3 Challenge
Clips :- It is the one of the important component of the wiring harness which has to define before the routing harness. This is use to give the support the harness . P Clamp :- It is clip which have the p shape and some time rubber is round around it. For defining the any clip we have to follow some step as follow:- …
03 Apr 2022 10:08 AM IST
Wiring harness design in CATIA V5 - 3D modeling Week 2 Challlenge
To define any electrical part or connector we need the CAD data which we can get from the net in this case we have the three connector as follow with their defination step :- …
26 Mar 2022 07:16 PM IST