Uploaded on
06 Sep 2022
Skill-Lync
A hybrid vehicle has two power sources for motion within the same vehicle. Basically, the hybrid vehicle is split into two types supported by the source for propulsion - combustion engine type and Hydrogen power cell. There are different combinations which are utilized in the hybrid vehicle like Gas-electric, Diesel-electric combinations. The ICtype is widely used in which IC engine, battery, motor and generator. Moreover, it's divided into 3 types:
A series hybrid is essentially a hybrid-powered vehicle with a simple drive train configuration which uses a battery to power the motor so as to run the wheels. The series hybrid vehicle diagram model is shown in the figure below.
This figure shows the essential block connections within the series of hybrid vehicle. It operates when the fuel tank sends fuel/gas to the engine and therefore the engine uses it to power itself and the power the generator and also the generator converts the mechanical to electrical charges the battery using a charger. The battery pack takes the energy received from the engine and sends it to the controllers which, in turn, control the voltage sent to the motors and inverter circuit based on the sort of motor used n the vehicle.
Finally the motor which is powered is connected to the wheels via train for driving the vehicle. The engine is responsible just for the charging the battery so the vehicle can move with or without the engine running. and therefore the motor is to blame for the acceleration of the vehicle. Typically there's no mechanical connection between an engine and wheels of the vehicle. This technique is intended to work at the most efficient and desired speed and cargo.
The series hybrid may be a simple system with no complexity in connection.
Multispeed transmission, clutch or converters aren't required since the electrical motor directly drives the power train for movement.
It operates as a pure Electric vehicle which runs on the battery source.
It helps to cut back harmful gas emissions and promotes an eco-friendly environment.
The series hybrid vehicle propulsion is entirely dependant on the battery source.
The energy conversions happening in each stage end up in an efficiency loss.
All these propulsion devices have to be sized to sustain maximum power requirements. In case of long gradeability conditions the performance of the vehicle is poor. Therefore the powerful motor is required at this example making the Series HEV, expensive.
This system may require a battery and motor with a large capacity to fulfil its power needs which adds to the burden of the vehicle and it decreases the general practice range of the vehicle. And this makes it undesirable for consumers to use.
It is recommended mostly for brief trips as commuting to figure and shopping the corresponding IC engine set with lower power rating is employed.
Due to the major disadvantages of the series hybrid vehicles, parallel hybrid and series-parallel combinations are introduced.
Author
Navin Baskar
Author
Skill-Lync
Subscribe to Our Free Newsletter
Continue Reading
Related Blogs
The average vehicle body gives any vehicle its structural integrity, while the electric motor is concerned with the generation of torque or force. The electric motor can be a permanent magnet synchronous motor, brushless dc motor etc.
24 Aug 2022
In industrial control applications, a PID controller is a device that regulates temperature, flow, pressure, speed, and other process variables. PID (proportional integral derivative) controllers, which use a control loop feedback mechanism to control process variables, are the most accurate and trustworthy controllers.
26 Aug 2022
A lithium-ion (Li-ion) battery is a complicated battery technology that uses lithium ions as a key component of its electrochemistry. During a discharge cycle, lithium atoms within the anode are ionized and separated from their electrons.
28 Aug 2022
Dash in your car is your source of information. It basically functions as a control panel that sits in front of the driver and shows numerous controls and instrumentation required for your car to function.
31 Aug 2022
The definition of electric power can be said as the rate at which energy is being consumed in a circuit. Any electrical or electronic device has a limit to the amount of electrical power that can be safely handled. Power is measured in watts.
13 Sep 2022
Author
Skill-Lync
Subscribe to Our Free Newsletter
Continue Reading
Related Blogs
The average vehicle body gives any vehicle its structural integrity, while the electric motor is concerned with the generation of torque or force. The electric motor can be a permanent magnet synchronous motor, brushless dc motor etc.
24 Aug 2022
In industrial control applications, a PID controller is a device that regulates temperature, flow, pressure, speed, and other process variables. PID (proportional integral derivative) controllers, which use a control loop feedback mechanism to control process variables, are the most accurate and trustworthy controllers.
26 Aug 2022
A lithium-ion (Li-ion) battery is a complicated battery technology that uses lithium ions as a key component of its electrochemistry. During a discharge cycle, lithium atoms within the anode are ionized and separated from their electrons.
28 Aug 2022
Dash in your car is your source of information. It basically functions as a control panel that sits in front of the driver and shows numerous controls and instrumentation required for your car to function.
31 Aug 2022
The definition of electric power can be said as the rate at which energy is being consumed in a circuit. Any electrical or electronic device has a limit to the amount of electrical power that can be safely handled. Power is measured in watts.
13 Sep 2022
Related Courses